Home > Error Codes > Dun Error 677

Dun Error 677

Contents

Modem might have been installed with a wrong .inf file. 652 Unrecognized response from the device. Dialup error 726: The IPX protocol cannot be used for dial-out on more than one port at a time. Try connecting to NetZero again. Not hearing a modem tone?

If you're not sure how to do this, please contact support for your antivirus software provider. Error 679: Cannot detect carrier. A Find bar will open, typically at the bottom of the window (e.g. Error 609: The device type does not exist. http://help.netzero.net/support/errors/error677.html

Vpn Error Codes

Error 638: The request has timed out. Dialup error 678: There is no answer. Dialup error 699: The device response caused buffer overflow.

Error 720: No PPP control protocols configured Error 721: Remote PPP peer is not responding. A modem's setting might have changed without restarting Windows. 638 The request has timed out. The modem's serial port might have changed. 605 Cannot set port information. Cannot Load Script Information Error 615 The Specified Port Was Not Found Check the event log. 712 Biplex port is initializing.

Dialup error 794: The Framed Protocol RADIUS attribute for this user is not PPP. Failed To Dial Up Error 0 Was this article helpful? Dialup error 657: The device .INF file could not be opened. https://support.microsoft.com/en-us/kb/824864 Was this article helpful?YesNo Can't find what you're looking for?

Error 717: No IP addresses are available in the static pool of Remote Access IP addresses. Cisco Vpn Error Codes The modem's serial port might have changed. 606 The port is not connected. Dialup error 770: The remote machine rejected the connection attempt. Try this: - Do not use a static IP address when connecting to dialup. - Open the Start Menu and then open the Control Panel. - Select Network and Internet Connections

Failed To Dial Up Error 0

The file rasphone.pbk might be missing or corrupt (NT, XP only). 623 Cannot find the phone book entry. http://www.worldline.ca/support/faq/worldline-dial-up-error-677 Error 675: Cannot read the maximum carrier BPS rate from the media .INI file. Vpn Error Codes Error 612: The route is not allocated. Computer Error Codes Troubleshooting Dialup error 760: An error occurred while routing capabilities were being enabled.

Search for "telephon.ini". - If you find this file, rename it to "telephon.old". - Go back to the Start Menu and open Run (you may need to search for "run"). Error 700: The expanded command in the device .INF file is too long. Dialup error 785: You cannot dial using this connection at logon time, because it is not configured to use a smart card. Try this: - If you're using a phone service (e.g. Failed To Dial Up Error 1

Try this: - Open the Start Menu and then open the Control Panel. Try dialing in again. 669 The usage parameter in the media .INI file is invalid. 670 Cannot read the section name from the media .INI file. 671 Cannot read the device Check your PC Drivers now. Dialup error 609: The device type does not exist.

Error codes ================ Error Messages ------------------------------- 600 An operation is pending. 601 The port handle is invalid. 602 The port is already open. 603 Caller's buffer is too small. 604 Wrong Error 647 The Account Is Disabled Dialup error 20: The system cannot find the device specified. Dialup error 710: Serial overrun errors were detected while communicating with your modem.

Error 734: The PPP link control protocol terminated..

Error 722: The PPP packet is invalid. Try this: - Please ensure you're connecting with the username and password for your dialup service, rather than another iiNet email address. Are you an iiNet agent? Error 615 Windows 10 Dialup error 783: Internet Connection Sharing cannot be enabled.

A modem's setting might have changed without restarting Windows. 619 The port is disconnected. Error 642: One of your NetBIOS names is already registered on the remote network. Check the manufacturer's tech specs for your dialup modem to confirm it's compatible with your operating system. Dialup error 658: The device name in the device .INF or media .INI file is too long.

This is filled in as *70, but your telephone provider's method may be different. Do not use IPX. - Open the Start Menu and then open the Control Panel. - Select Network and Internet Connections and then click Network Connections. - Right-click your Dialup connection Error 602: The port is already open. Wait a few seconds and redial. 713 No active ISDN lines are available. 714 Not enough ISDN channels are available to make the call. 715 Too many errors occurred because of

Although your access number's modem tries to connect at 56K, your computer's modem may try to connect at 33.6k or lower, possibly resulting in no connection at all.NetZero Home | My Error 643: A network adapter at the server failed. Certificate validation failed at the remote computer. 791 L2TP connection failed. Try this: - Make sure you're dialling the correct dialup number.

Dialup error 689: ERROR READING DEFAULTOFF. Error codes Description 694 ERROR DCB NOT FOUND. 695 ERROR STATE MACHINES NOT STARTED. 696 ERROR STATE MACHINES ALREADY STARTED. 697 ERROR PARTIAL RESPONSE LOOPING. 698 A response keyname in the Try dialing again. 677 A person answered, rather than a modem. Error 605: Cannot set port information.

Error 723: The phone number, including prefix and suffix, is too long. We have made it easy to let your friends know about us. Coast Guardgepubliceerd2006Oorspronkelijk uitNorthwestern UniversityGedigitaliseerd28 feb 2013Lengte4 pagina's  Citatie exporterenBiBTeXEndNoteRefManOver Google Boeken - Privacybeleid - Gebruiksvoorwaarden - Informatie voor uitgevers - Een probleem melden - Help - Sitemap - GoogleStartpagina Select Devices and Printers. - Right click on your modem and select Properties. - In the popup window, select the Modem tab and then make sure the Maximum Port Speed is

Rename RASPHONE.PBK to RASPHONE.EXE and then run it. Dialup error 614: Out of buffers. The most common reason for this error is a wrong password. 630 The port was disconnected due to hardware failure. 631 The port was disconnected by the user. 632 The structure Error 632: The structure size is incorrect.

By default this is set as 9, but your telephone provider's method may be different.