Home > Error Code > E1 Error Code Whirlpool Washing Machine

E1 Error Code Whirlpool Washing Machine

Contents

The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. Average current trip occurs if there is a 2 second average of current draw greater than 5.55 Amps at the motor windings. F10 - Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source. In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared. useful reference

We found a ladies pair of underwear in that drain. Verify pressure switch operation. 7. F70 CENTRAL CONTROL UNIT HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface. 1. Bezig...

Pe Error Code Whirlpool Washing Machine

F5 - Control Board Failure - Replace control board (clock). Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness you did clean out the filter? Ask Your Own Appliance Question Customer: replied5 years ago. - no - i don't know where it is Expert: Appliance Tech Larry replied5 Kyle Wilson U.S.

Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table on page 10. Er Processor reset error This error code is displayed if the control failed to save cycle information during a power failure. Whirlpool Duet Washer Error Code E1 F8 Press START to continue the cycle from the moment that power was lost.

Happy to help. Glad the post worked for you. Reply Matthew says: June 15, 2015 at 4:09 pm Awesome!

Reply Matthew says: January 23, 2016 at 1:34 am Sweet!

Would this be cause by the output end of the pump where sludge may of accumulated and is unable to flush out? Maytag Washer Error Code E1 F9 Check resistance of heating element, if present on this model. (abnormal = infinity) 4. If failure remains, disconnect power and replace control. If the condition continues four times, the F31 code will show.MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will

F22 Error Code Whirlpool Washing Machine

Over Pers Auteursrecht Videomakers Adverteren Ontwikkelaars +YouTube Voorwaarden Privacy Beleid & veiligheid Feedback verzenden Probeer iets nieuws! http://producthelp.whirlpool.com/Troubleshooting_Guides/Troubleshooting_for_Top_Load_HE_Washers_(Electronic_Control)/Error_Codes/F%23_E%23_or_F%23%23/F8_E1_Error_code_for_top_load_washers I checked the filter and there was one sock, but it was totally shredded up. Pe Error Code Whirlpool Washing Machine Reconnect power and plug unit in. Whirlpool Washing Machine F21 Error Code F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser.

Matt Reply Bill reilly says: April 17, 2015 at 1:55 pm Thanks! see here Any ideas where I could start? Check wire harness connections to the User Interface and the Central Control Unit. 3. All I could see was dollar signs $$$$. Whirlpool Washing Machine F11 Error Code

Replace Central Control Unit if drum is not moving. If the black drain hose on the rear of the washer is kinked or clogged, then F9 E1 will be displayed. Reply Matthew says: May 3, 2015 at 9:54 pm Bryan, You're most welcome. this page Proceed by checking the drain hoses for proper connection and kinks.

The doorswitch may cause an interference for the powersupply of the MCU. Whirlpool F9e1 Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check for plugged This should clear the unit of the excess detergent. 1.

F2 - E1 Keypad cable unplugged F2 - E5 Cancel key drive line open F2 - E6 Cancel key drive line open F3 - E0 Oven temperature sensor (RTD) opened (upper

Check for stuck lock switch. There are 3 on our model and we disconnected them (they just snap out like a phone line in a phone jack) so we could completely remove the front panel. 7. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Maytag 2000 Series Washer Error Codes 5d Verify CCU operation by running a Diagnostic Test or any cycle. 6.

The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. How do I access the drain/filter in this machine? Use drain hose form and attach securely to drainpipe or tub. Get More Info F62 STEAMER ELECTRONIC BOARD RELAYS ERROR One of the steamer relays (K1, K2, K3, K4) on the Steamer Electronic board have failed, there is an open or short circuit.

Door lock mechanism is broken. Check mechanical linkage from dispenser motor to the top of the dispenser. 3.