Home > Error Code > Dvc Error Code

Dvc Error Code

Contents

Possible culprits are insufficient gas supply, a blockage in the fuel vent or debris in the fan motor. Solution: Measure the incoming voltage. New registrants who use these addresses to register will be automatically deleted from the database. You will need a licensed contractor to resolve this error. click site

I have checked and found a regulator on the HVAC at right before unit (has been there since installed years ago), and gas range has built-in regulator at rear of unit It appears to me that the gas pressure on the main line is not regulated at meter but was regulated at individual units by the original design. Error Code 16 The problem: Extremely high water temperature. one psi, with the figures you posted that is way too much for your heater, most domestic gas systems run in the 1/2lb. http://support.noritz.com/article/faq-what-does-an-error-code-12-mean-218.html

Noritz Error Code 10

Error Code 12 The problem: Burner flame loss during operation; flame rod does not detect flame. I rechecked for leaks, and re-hooked up my homemade manometer to the HW heater service port. All rights reserved. Clean the fan motor and burner chamber.

The request cannot be fulfilled by the server Login to DoItYourself Username: Password: Forgot username or password? David 06-21-09,11:55 AM #4 shacko Member Join Date Aug 2005 State MD Posts 2,138 Gas Problem Nogascans: I may have been wrong to suggest that you use a manometer; it could These ISPs consider our notifications to be spam, and you will not receive activation emails. Noritz Error Code 51 You have to leave all the other gas fixtures on or you might get a false reading. 28 Inch of water column is aprox.

Solution: Replace the inlet thermistor. Noritz Error Code 11 Common issues associated with a 12 error code include: 1) Insufficient gas supply 2) Insufficient air supply 3) Debris on the flame sensor It is recommended that you contact a servicer Do not reset the water heater error code before the service; otherwise the unit might fail prematurely. Also, the water heater should be adjust for the right height elevation.

Login | FAQ + Reply to Thread Results 1 to 8 of 8 LinkBack LinkBack URL About LinkBacks Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Noritz Error Code 14 The DVC Boards at MouseOwners.com - the place to talk DVC and Walt Disney World > TECH SUPPORT > Tech Support Error Code User Name Remember Me? Make sure that only one remote control is hooked up when two units are connected. Or Login with Facebook Don't Have an account?Sign Up Today Cancel Search How-Tos Your Projects Forums search Hi Unregistered | Logout Connect with Facebook Login Sign Up Forum New Posts Today's

Noritz Error Code 11

Solution: The error code 71 happens if the water heater is connected to the battery backup, solar power or generator and if there is a fluctuation in voltage supply. The Nortiz 751M specifies a gas supply pressure of NG : 4.0" - 10.5" with a (199,900 Btuh) rating. Noritz Error Code 10 Solution: Your Noritz water heater might need descaling due to the sediment and lime scale build up. Noritz Error Code 90 Thanks!

Solution: Reset the heater by disconnecting the power and check the circuit board programming. get redirected here Error Code 73 The problem: The problem with the circuit board setting. Applicable Models Models: ALL MODELS Posted - Fri, Dec 16, 2011 5:43 PM. Noritz Error Code 90 A code 90 indicates a combustion abnormality caused by an improper mixture of air and fuel. Noritz Error Code 12

Remove any obstructions in the venting system. Password Register FAQ Calendar Today's Posts Search Notices Please do not use Hotmail, Outlook, or MSN email addresses to register on MouseOwners. It's free! navigate to this website Gas meter is approximately 17 ft (12 ft/tee (to range, HVAC)4 ft from tee to 90 degree (3/4" black pipe), 1 ft up to tankless water heater (the new unit with

He or she will check gas pressures, venting length, dip switches, etc. Noritz Error Code 903 The Manufacturer (Noritz) specifies a Natural Gas pressure of MIN 4" WC, and MAX 10.5" WC, As mentioned before, there is a gas inlet with a acessable tap for checking with If you tied into an existing line you have to make sure that it has enough capacity to feed your heater and the fixture that it is tied to.

All rights reserved.

Add Comment Full Name Email Address (Required, but not published) Comment Security Code Related ArticlesThere are no articles in this section. My issue is that i can get the system to function, but intermittently the Noritz fails to maintain burner operation (red light off, low/no hot water) and eventually the control unit and work toward the meter adding numbers as you go this will give you the size of the next pipe, (you need a gas chart to get these figures) I know Noritz Error Code F 76 After checking to see if the gas is turned on, call a licensed contractor.

Unplug the heater for 30 seconds and then plug it back in. Worked great kltmnt View Public Profile Send a private message to kltmnt Find More Posts by kltmnt « Previous Thread | Next Thread » Thread Tools Show Printable Version Email I hope that helps. http://thewebparrots.com/error-code/e-04-01-error-code.php Since your problem has been worked out with a regulator at your heater and everything else is working you don't need one.

Approximate distance from gas meter to unit is 17 ft. I still lean toward not enough gas, you didn't tell me where you tied in your 3/4 line, but if you tied it into another 3/4 line theres a good chance Copyright © 1995-2016 DoItYourself.com Inc. FAQs and Community/Posting Guidelines Site / Forum News and Events MouseOwners Events and Event Planning VACATION CLUB RESOURCES Latest DVC News and Rumors

With valve open, I had a 5" increase in water height, so I should be right around 10 WC. http://www.osc.state.ny.us/payroll/f.../502errmsg.pdf . Glad its working! I have no problem with function of range or gas heater.

Solution: Check for the incoming gas pressure. Solution: This is not an error code but is the automatic service reminder that informs you that it is time to call the Noritz licensed technician. The tools needed to solve the problems from below are mainly the screwdriver, manometer and voltmeter. This means that the unit is detecting a flame, but the flame is being extinguished during operation (weak flame).

Or am I barking up wrong tree? In other words, we will not be able to activate/verify your account. Error Code 72 The problem: The flame rod detects the flame without the ignition sequence. Get notified when Knowledgebase articles are added or updated.

Remove any blockage in venting.