I checked my Device Manager, there is no port 2. Adi R Mar 30, 2012 @ 12:47:35 Port number changes just from the way your Hard-drive(s) is connected to the motherboard. Tails77 View Public Profile Find More Posts by Tails77 02 May 2012 #4 writhziden Windows 7 Home Premium 64 Bit 11,288 posts Colorado It could be a few Inserte un disco en la unidad /device/Harddisk5/DRS, ALGUNO DE UDS SABRIA DARME UNA ORIENTACION A KE SE DEBE Y COMO RESOLVERLO,? have a peek at these guys
Check the medium changer is running unknown dirves i.e Microsoft drivers 0 Kudos Reply Check the Windows event AmolB Level 6 Employee Accredited Certified 05-20-2010 07:06 AM Options Mark as New See this document http://www.symantec.com/docs/TECH70907 0 Kudos Reply The server in question is a rparker13 Level 3 Partner 11-09-2011 07:04 AM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed So it is my 931GB drive? –Sun May 29 at 14:44 Its somekind of identification to which partition it is referring. Same drive inserted multiple times into the same port will have same DR. http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/the-driver-detected-a-controller-error-on/3502622d-6f09-471f-98d7-2f513a276005
System Info - See Your System Specs will help with filling in your system specs. In my even viewer it says "The driver detected a controller error on\Device\Harddisk1\DR1" This error appears about 15 times a day. For impatient souls among us, here are my conclusions: First thing – check the SATA/EIDE and power cable connection between your hard-drive and the motherboard.
Very handy, and then you have up to 28 days to put your real key in and activate. What do I do now?2Driver detected a controller error on disk that doens't exist1Disk Error on a Dell Notebook with Windows 8.1 “The device, \Device\Harddisk0\DR0, has a bad block.”1Chkdsk An unspecified I tried different sata cables, but it didnt help. The Driver Detected A Controller Error On \device\ide\ideport2. Sure enough we received the error "The driver detected a controller error on \Device\Ide\IdePort0", after a close review we also got one for each HD in the machine (there are 5),
Edited Jun 20, 2013 at 8:48 UTC 2 Sonora OP derektom Jun 21, 2013 at 1:27 UTC Hi Ingmar, much thanks for that additional info. The Driver Detected A Controller Error On Device Harddisk2 Dr2 Also, once you figure out hard-drive health, you can use same utilities to save whatever data is on there. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks. My System Specs System Manufacturer/Model Number HP Pavillion dv-7 1005 Tx OS Win 8 Release candidate 8400 CPU [email protected] Memory 4 gigs Graphics Card Nvidia 9600M Sound Card HD built-in Monitor(s)
About an hour ago we noticed it was off the air, when we returned to the studio to check it we had a black screen. The Driver Detected A Controller Error On \device\harddisk3\dr3. I have never heard of such a thing, but perhaps it does exist out there somewhere. There should be no performance hit on that. and, they also have another group of really really bright folks working on another aspect of the disk drive management issue.
Sometimes older motherboards will have some mix of sata ][ ports and sata ]|[ ports. website here These are available free from manufacturers web-sites, if you know the brand, or generic HDD utilities are available from download.com. The Driver Detected A Controller Error On Device Ide Ideport0 But this is just an assumption. The Driver Detected A Controller Error On Device Harddisk0 Check the Scsi Id for the Medium changer it has to be on a lower Id than yo tape drive 2.
Feb 19, 2013 at 4:05 UTC Do you have any Management software installed for the RAID? That would have it's own logging and hopefully diagnostics too. 0 Jalapeno More about the author We had assumed it overheated. Event Viewer reports "Atapi - Event ID 11 - Driver detected a controller error on \Device\Ide\IdePort0". The backups work fine but these messages just started appearing (or they were just noticed). 0 Kudos Reply ...and the ACU shows no CraigV Moderator Partner Trusted Advisor Accredited The Driver Detected A Controller Error On \device\ide\ideport1.
After that I was able to write to cd, dvd, and able to delete rewritable cd. ( I left HD on the same port!, but hard disk can also cause this The system had two hard-drives, and the older hard-drive was seemingly working just fine, even with the same SATA cable and connected to the same slot on the Motherboard. Alo try updating the Firmware and drivers for the SCSI card as well .. check my blog Thankyou for taking the time to help me out.
Did you know you can avoid “tarnishing” your license in such scenario by Skipping product key page during Windows 7 setup? The Driver Detected A Controller Error On \device\harddisk1\dr2. Is "DR2" = "Disk 2"? If you are into free software on Linux, like several commenters were, I would recommend ZFS, which is part of an excellent FreeBSD distribution.
BSOD Help and Support The driver detected a controller error on \Device\CdRom0.The title says it all friends... You should take this warning and start doing backups. Have done all the usual troubleshooting as you would expect. news i have recently been burning some dvd's DVD+R by the way and all was going well until i reinserted a disk and when i went to Start,Computer and E Drive it
I was able to pick up 8 GB of Gamer grade memory for $25 (after rebate), so that is another bonus with upgrade. Expand storage on the left and select disk management. Retrieving values() from a Map of Sets in SOQL query Standard way for novice to prevent small round plug from rolling away while soldering wires to it How to cope with Adi R Dec 10, 2012 @ 09:14:22 Glad to hear it helped - Great idea to plug it into a different port on MB !
I check the disk manager and from what I see in there my primary harddisk is located in channel0/Disk 0 while Disk1 is from my removable USB flash drive. Ridiculously, many people are likely affected by this issue, but unless they open Event Viewer and search for this event id 11, they will not realize that hanging is not “normal” To chat live with a Partner Support Consultant, complete the form below and click Connect. Next step was to run diagnostic from manufacturer (WD in this case), which reported SMART info was good but there are some bad sectors.
I was under the impression that "DR" stands for "disk removable", but I honestly wasn't able to find any references to that so I could be wrong. If indeed this external caused the error message, I want to make sure. Every disk will have a device controlling the Raw Physical drive (DR identifier) and a device per each partition, controlling the partition (DP instance) For example: Harddisk1\DR2 and Harddisk1\DP3 Unlike in the case Here is another question Why the god damn bloody hell does MS make this information so F'ing hard to correlate to a physical drive?