I plugged it in (while the power was turned off!), and booted up. Re-boot. The program could then gracefully recover from the problem. It would be nice, but all I really want is to recover my old files (especially pics) from that computer.
Change to \DOS where SCANDISK is. See our elevated mode for information about this mode and how to enter the mode. Stack overflow DOS does not have enough room to handle hardware interrupts. Click here to Register a free account now! check my blog
mouse.drv=C:\MSINPUT\MOUSE\MSINPUT.DRV Not good, but expected. But since then, my "working" floppy drive and cable has been error messages. I cleaned the four drives that were giving me failures, and none of them started working again in a known working computer. Custom Search
Make sure the cables are correctly attached to the drive. If its another operating system then you are stuffed.What happens when the computer starts up, what errors do you get?I can't remember if Format.com is on the bootdisk but the other If none of the cards seem to be suspect, the problem may lie with the motherboard itself.FDD CONTROLLER FAILURE This often means your floppy drive controller has failed, or possibly the Dos Error 64 Yes No Voted Undo Score 1 Cancel Comments: Thanks for the reply;yeah I could do that, but want to fix the error if possible;I cant(and wouldn't) get this online, with it
First Name Email Is Your Computer Infected With Malware? Error Reading From Drive C Dos Area There may be dirt or dust on the surface of the disk. Check to see if you can find a BIOS update. Reply With Quote May 5th, 2012,09:31 PM #5 twolazy View Profile View Forum Posts Private Message View Blog Entries View Articles Senior Member Join Date May 2011 Location Somewhere near Chicago
Not ready writing device PRN Abort, Retry, Fail? Dos Error 4 The message was sometimes used as an example of poor usability design in computer user interfaces. The /F option tells chkdsk to automatically fix anything bad that it finds, either in boot records, faulty files etc. Start Windows.
BUT the next thing that I did was to do a complete backup of the hard disk. http://www.computerhope.com/doserror.htm You haven't really said which operating system has been on the computer before. Error Reading From Drive A Dos Area General Failure signals across the address line 20. Data Error Reading Drive C Hmmm.
Of course you will have to have a DOS startup disk. The computer has no way of determining whether it should wait for the user to load a disk, or abort the operation. What's new? Try again. Dos Error 5
Invalid parameter Typed a command correctly but specified the incorrect parameter, such as format /z. Like I said, the last working drive I put in worked for a while until I tried to copy the contents to a directory via DOSShell. So what do I do now!? Duplicate file name The file cannot be renamed because a file with that name already exists.
For example using the xcopy command to copy files in the Documents and Settings folder. Dos Error Level As a long time DOS user (still am) I can tell you for sure that there is no "trial and error" involved. Sometimes tapping the edge of the disk on a hard surface a few times will loosen whatever is causing the problem and let you read the disk.
See the attrib command for further information and options on this command. If the above title has the general effect of raising the hair on the back of your neck, then that's probably a sign that you are ready for this. (Updated 2/9/1999.) If it doesn't reboot, boot the system off a system disk then switch to C:. Dos Error Code 1 Unable to read floppy diskette.
Thanks! If this doesn't help, then you'll have to replace the motherboard.GENERAL FAILURE READING DRIVE X: First, press I for ignore, then use a diagnostic utility to test the disk. ScanDisk might patch it, but if the hard drive has too many bad sectors or files, it could take very long. Press R to retry or A to stop (abort).
Make sure it is a valid system disk.DISK CONFIGURATION ERROR Usually caused by trying to use a newer technology drive on a system that is too old. This error often occurs when you're typing a directory in the MS-DOS or the Windows command line that has spaces in it. How to change or rename a file, folder, or directory. This error will also occur if a disk was never formatted properly.
Ummm.... Oh, well--stuff happens. I tried the link to download the boot disk, but the file was no longer there. Ideally you are using floppies only as secondary storage and can just use the original, clean copy stored on the hard disk.
Then run a disk diagnostic utility. Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode May 5th, 2012,07:44 PM #1 btrains View Profile View Forum Posts Private Message View Blog